Others not caused by instrument or part itself. China Website: www. Due to compatibility of the Network Protocol used in the UltraAssist, UltraAssist needs to be used in accompany with certain versions of the ultrasound system, as shown below: For version 2. For version 1. Make sure that the computer on which you intend to install UltraAssist and the ultrasound system are both connected into a LAN. Find the setup file for UltraAssist , double click it to open the file and follow the instructions on screen to install UltraAssist.
Note: during installation, you may have to install QT tool, please follow the prompts to install the tool. Select destination folder and click [Next]. Make sure that the computer on which you installed UltraAssist and the ultrasound system are both connected into a LAN. Click [iStorage] tab to enter the page and fill in information: Machine Name: name of the ultrasound system. IP Address: IP address of the ultrasound system. Directory: saving path for receiving files from ultrasound system.
Perform exams in ultrasound system. Enter iStation, select exam or images to send, and select the destination in the dialogue box to be iStorage take DC-8 as an example. User-defined Measurement Item 1. Open UltraAssist in computer, click [iMeasurement] tab. Click [New Measure] to pop up the following dialogue box. Set the following parameters.
Description of the items in the dialog box is shown in the following table. Item Description Name Measurement item name. General measurement tool type of the user-defined item. Tool Type For example, select Area if you want to add a new item to measure the area.
Region Application region for the measurement item. Click [OK] to finish the setting. The user-defined measurement item appears in the main screen list. Click [New Calculation] to pop up the following dialogue box. Item Description Name Calculation item name. Region Application region for the calculation item. Unit Type Unit used for the calculation. Formula Displays the user-defined formula. Verify Verifies the input value. View Type Mode in which the calculation item is used.
Item Type Type for the calculation item. Select Item Name All available measurement items in the Formula application region selected in the previous Referenced step.
Double click to add to the formula. Calculator Inputs numbers in the formula. Verify the formula and select the unit and range of the result, click [OK] to finish and the item will be displayed in the list. Click right button of the mouse on a user-defined item in iMeasurement page. Delete: click to delete the item. Export: click to save the item in another path. Send to: click to send to the ultrasound system with specified IP address.
Sending iMeasurement Item 1. Click [Send To] to pop up the dialogue box. Enter the IP address of the ultrasound machine and click [OK] to send. UltraAssist prompts the sending is successful. In the ultrasound system take DC-8 as an example : 1. The system will prompt you that a user-defined measurement is received; click [OK] to receive.
Select the application region for the user-defined item and click [OK] to finish. To delete user-defined items on the ultrasound system: click to select the item, and click [Delete] on the right. Note: After user-defined calculation item is imported into the ultrasound system, it cannot be configured into measurement package, but as long as the item related measurements are finished, result window and report will display the result automatically.
Connect the removable storage device to the ultrasound system. Tips: iReport is only used for modifying page header layout of report template. User-defined Report Template 1. Open UltraAssist in computer, click [iReport] tab. Select [Patient Info] tab to set layout for patient info in the 1st report page header; Select [Page Header] tab to set layout for page header in the 2nd report page.
Click [New] to pop up the New Base On Preset Template, select the predefined layout type and click [Finish] to enter the following report editing status:.
Right click on the layout module and click [Add Row] to add another row to the report; Right click on the layout module and click [Delete Row] to delete an added row;.
Click [Cancel] to cancel current modification. Double-click the layout module frame e. If [Keyword visible] is checked, then module name will be displayed in the report template. After [Keyword visible] is checked, check [Auto Filter] also to set the system auto-display the module name.
Double click Hospital logo to pop up the logo setting dialogue box, where you can set logo width and height. Click [Open] to open the already defined report template or to change it. Click [Save] to save current report template to the UltraAssist file path.
Enter the report template name, and IP address of the ultrasound machine and click [OK] to send. The ultrasound system will prompt you that a user-defined report template is received, click [OK] to start receiving.
Select the application report for the user-defined template and click [OK] to finish. Select the template you want to use from the Custom Report Template list on the right side, and select the report type to be applied from the left side of the Report Type list to apply the template to the report type. After creating a user-defined report template in UltraAssist, click [Save As] to save the template into the removable storage device e.
USB disk ; or you can find the template with a. Network connection failure. If network connection is normal, please disable firewall on the computer. Disconnect U disk after sending is finished. English UltraAssist UltraAssist. Pular no carrossel. Anterior no carrossel.
The module contains a small set of exclusive Exchange Online PowerShell cmdlets that are optimized for bulk data retrieval scenarios think: thousands and thousands of objects. When you first open the module, you'll only see these exclusive cmdlets.
After you connect to your Exchange Online organization , you'll see all of the familiar cmdlets that are available in Exchange Online PowerShell. The module use modern authentication for all cmdlets. You can't use Basic authentication in the EXO V2 module; however, you still need to enable the Basic authentication setting in WinRM as explained later in this article.
The Exchange Online cmdlets in the EXO V2 module are meant to replace their older, less efficient equivalents, but the equivalent cmdlets are still available after you connect. The connection-related cmdlets that are available in the EXO V2 module are listed in the following table:.
Version 2. This Preview version improves upon the historical capabilities of the module with the following features:. When you use the UseCustomRoutingSwitch , you need to use the following values for identity of the mailbox:.
Use this parameter experimentally and report any issues that you encounter. Specifically, version 2. If you have trouble using the EXO V2 module on other distributions of Linux, send email to the following address: exocmdletpreview[at]service[dot]microsoft[dot]com. The email address is purposefully obfuscated to avoid spam. PowerShell 7 on Windows requires version 2. Only version 2. NET Framework 4. For more information, see Windows Management Framework 5.
The settings described in this section are required in all versions of PowerShell on all operating systems. PowerShell needs to be configured to run scripts, and by default, it isn't. You'll get the following error when you try to connect:. Files cannot be loaded because running scripts is disabled on this system. Provide a valid certificate with which to sign the files.
To require all PowerShell scripts that you download from the internet are signed by a trusted publisher, run the following command in an elevated PowerShell window a PowerShell window you open by selecting Run as administrator :. For more information about execution policies, see About Execution Policies. WinRM needs to allow Basic authentication it's enabled by default.
We don't send the username and password combination, but the Basic authentication header is required to send the session's OAuth token, since the client-side WinRM implementation has no support for OAuth.
As described earlier in this article , v2. You must temporarily enable WinRM to run the following commands. You can enable WinRM by running the command: winrm quickconfig. The WinRM client cannot process the request. Basic authentication is currently disabled in the client configuration. Change the client configuration and try the request again. Having problems? Ask for help in the Exchange forums. Typically, you'll want the latest public version of the module, but you can also install a Preview version if one is available.
To install the latest public version of the module, run one of the the following commands:. For detailed syntax and parameter information, see Install-Module. If the module is already installed on your computer, you can run the following commands to see the version that's currently installed and update it to the latest version from the PowerShell Gallery:. Typically, you'll want the latest public version of the module, but you can also upgrade to a Preview version if one is available.
To upgrade to the latest public version of the module, run one of the following commands based on how you originally installed the module in an elevated PowerShell window vs. Scope CurrentUser :. To confirm that the update was successful, run the following commands to check the version information of the module that's installed:. For detailed syntax and parameter information, see Update-Module.
Be sure to close and re-open the PowerShell window before you attempt to update the ExchangeOnlineManagement module again. To check your current settings in the Microsoft. To permanently enable strong cryptography in the Microsoft. NET Framework version 4.
0コメント